Molten metals simply slide off of the extra heavy duty coating of High-Temperature Silicone Rubber on all of these products (firesleeve), providing excellent burn-through protection.
Fiberglass Tape with Silicone Rubber Coating On One Side:
Heat & Weld Splatter Resistant
High Temperature & Flame Resistant Silicone Rubber Coated Fiberglass Tape: Non-Adhesive
Heat & Weld Splatter Resistant
High Temperature & Flame Resistant Silicone Rubber Coated Fiberglass Tape: Non-Adhesive
This fiberglass tape with heavy duty silicone rubber coating is heat, high temperature & flame resistant; similar to our firesleeve except it can be installed in situations where tubular firesleeve cannot be used, as when industrial hoses, wires and cables cannot be disconnected to install a sleeve. (our firesleeve with velcro closure is also an alternative).
This heat resistant tape is the perfect choice for protection of industrial hydraulic hoses and lines, pneumatic lines, fuel & oil lines, brake lines, wires, cables, tube and pipe from exposure to high and extreme heat conditions. The extra thick special formulation of silicone rubber sheds molten metals, slag, welding splatter, electrical or grinding sparks and contamination. This tape also provides protection from ozone, UV and abrasion and provides thermal insulation.
Standard color for this high temperature heat resistant tape is oxide-red, however it can be painted with our liquid silicone to result in almost any color. Normally supplied in 100 foot lengths.
Fabricated from a knitted fiberglass (fibreglass / glassfibre) yarn substrate, and is available in 5 standard widths: 1", 2", 3", 4" and 5". Due to the knit construction of the base material, this tape has the ability to stretch slightly across its width, but only minimally in its length.
This heat resistant tape can also be used to wrap complex shapes or varying dimension tapered pipes. Typically, the tape is overlaped by 50% when winding, which provides the entire assembly with stability. Safety wire, band clamps, ties or End Wrap Tape can be used to secure the tape in place after installation.
This heat resistant tape is the perfect choice for protection of industrial hydraulic hoses and lines, pneumatic lines, fuel & oil lines, brake lines, wires, cables, tube and pipe from exposure to high and extreme heat conditions. The extra thick special formulation of silicone rubber sheds molten metals, slag, welding splatter, electrical or grinding sparks and contamination. This tape also provides protection from ozone, UV and abrasion and provides thermal insulation.
Standard color for this high temperature heat resistant tape is oxide-red, however it can be painted with our liquid silicone to result in almost any color. Normally supplied in 100 foot lengths.
Fabricated from a knitted fiberglass (fibreglass / glassfibre) yarn substrate, and is available in 5 standard widths: 1", 2", 3", 4" and 5". Due to the knit construction of the base material, this tape has the ability to stretch slightly across its width, but only minimally in its length.
This heat resistant tape can also be used to wrap complex shapes or varying dimension tapered pipes. Typically, the tape is overlaped by 50% when winding, which provides the entire assembly with stability. Safety wire, band clamps, ties or End Wrap Tape can be used to secure the tape in place after installation.
Withstands Molten Splash & Welding Splatter. Withstands 500°F / 260°C continuous exposure;
2200°F / 1205°C for periods up to 15 minutes and short flash excursions to 3000°F / 1650°C.
2200°F / 1205°C for periods up to 15 minutes and short flash excursions to 3000°F / 1650°C.
High Temperature Silicone Rubber Coated Fiberglass Heavy Duty Woven Tape & Wrap: Non-Adhesive
Heavy Duty Woven fiberglass (fibreglass or glass-fibre) tape coated with high temperature silicone rubber.
Thisheat resistant tape is fabricated from a woven fiberglass substrate, and in available in widths up to 40" wide and lengths up to 150 feet continuous. Due to the base material being woven, this tape has very little elasticity or ability to stretch in any direction, although it is easily wrapped over even small diameter hoses, pipes, cables or wires.
Thisheat resistant tape is fabricated from a woven fiberglass substrate, and in available in widths up to 40" wide and lengths up to 150 feet continuous. Due to the base material being woven, this tape has very little elasticity or ability to stretch in any direction, although it is easily wrapped over even small diameter hoses, pipes, cables or wires.
High Temperature Silicone Rubber 2-Side Coated Fiberglass Tape & Wrap: Non-Adhesive
Fiberglass (fibreglass or glass-fibre) tape coated on two sides with high temperature silicone rubber.
This heat resistant tape is fabricated from a woven fiberglass substrate, and in available in widths up to 40" wide and lengths up to 150 feet continuous.
This heat resistant tape is fabricated from a woven fiberglass substrate, and in available in widths up to 40" wide and lengths up to 150 feet continuous.
Withstands Molten Splash & Welding Splatter. Withstands 500°F / 260°C continuous exposure;
2200°F / 1205°C for periods up to 15 minutes and short flash excursions to 3000°F / 1650°C.
2200°F / 1205°C for periods up to 15 minutes and short flash excursions to 3000°F / 1650°C.
Materials that resist catching fire, burn slowly, or retard burning can be described as either "incombustible", "non-flammable", "non-combustible", "fire-resistant" or "fire-retardant". "Self-extinguishing" materials cease burning once the flame or heat source is removed. "Fireproof" is understood to mean that an object cannot burn, but few materials are truly fireproof.
Most of our products fall within one or more of the above descriptions: they resist high temperature, flame, fire, molten metal splash and weld splatter very well but may melt with prolonged exposures past their designed maximum continuous operating temperature. They can also provide OSHA, ANSI-FM & NFPA compliance and personnel protection.
Using our products to retain heat or cold within pipes, hoses, enclosures or equipment helps conserve energy and resources, and reduces operating costs.
AB Technology Group: Keeping Our World Cooler ä. All products are non-asbestos and 100% asbestos free, and also make excellent asbestos substitution and replacement materials.
Most of our products fall within one or more of the above descriptions: they resist high temperature, flame, fire, molten metal splash and weld splatter very well but may melt with prolonged exposures past their designed maximum continuous operating temperature. They can also provide OSHA, ANSI-FM & NFPA compliance and personnel protection.
Using our products to retain heat or cold within pipes, hoses, enclosures or equipment helps conserve energy and resources, and reduces operating costs.
AB Technology Group: Keeping Our World Cooler ä. All products are non-asbestos and 100% asbestos free, and also make excellent asbestos substitution and replacement materials.